ALUMINUM ELECTROLYTIC CAPACITORS
UT
6mmL Chip Type , Wide Temperature Range
series
Chip type with load life 2000 hours at +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
UA Long Life
UT
Long Life
WT
UX Higher C/V
Specifications
Item
Performance Characteristics
Category Temperature Range
– 55 to +105°C
Rated Voltage Range
4 to 50V
Rated Capacitance Range
0.1 to 100µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
Measurement frequency :120Hz at 20°C
Tangent of loss angle (tan δ)
4
0.37
Rated voltage (V)
tan δ (MAX.)
6.3
0.28
10
0.24
16
0.20
25
0.16
35
0.13
50
0.12
Measurement frequency :120Hz
4
6
12
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
Z– 40°C / Z+20°C
ZT / Z20 (MAX.)
Stability at Low Temperature
6.3
3
8
16
2
4
25
2
3
35
2
3
50
2
3
Within ±25% of the initial capacitance value (16V or less)
Within ±20% of the initial capacitance value (25V or more)
200% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance
change
tan δ
Leakage current
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 2000 hours at
105°C.
Endurance
10
3
5
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change
Within ±10% of the initial capacitance value
maintained at 250°C. The capacitors shall meet the characteristic
Less than or equal to the initial specified value
tan δ
requirements listed at right when they are removed from the plate
Less than or equal to the initial specified value
Leakage current
and restored to 20°C.
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Type numbering system (Example : 16V 10µF)
Chip Type
1
Positive
Plastic platform
0.3MAX.
C±0.2
B±0.2
0.5 to 0.8
5.8±0.3
Voltage mark for 6.3V is
A±0.2
φD±0.5
A2P
10
16V
Voltage
E
Lot No.
A±0.2
Capacitance
2
3
4
5
6
7
8
9 10 11 12 13 14
UU T 1 C 1 0 0 M C L 1 GS
0.5MAX.
105°C Marking
φD 4
A
B
C
E
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
Taping code
(mm)
6.3
2.4
6.6
6.6
2.2
Configuration
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
Negative
Type
6V .
Dimensions
V
Cap.(µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
4
0G
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
5
5
6.3
6.3
0J
22
30
36
60
4
5
5
6.3
10
1A
22
30
36
60
5
5
6.3
6.3
16
1C
27
35
46
60
25
1E
35
1V
50
1H
18
30
40
50
4
5
6.3
6.3
13
23
38
48
4
5
6.3
15
25
42
1.0
2.6
3.2
3.8
6.2
11
14
19
30
Case size
φ D (mm)
4
5
6.3
6.3
4
4
4
4
4
4
4
5
6.3
Allowable
Rated
ripple
ripple
Rated ripple current (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UX(p.110), UJ(p.116) series if high C/V products are
required.
Please refer to page 3 for the minimum order quantity.
CAT.8100B
