CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CF
Chip Type, Standard
series
Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C
peak correspondence.
Compliant to the RoHS directive (2002/95/EC).
CS
CG
Higher
Capacitance,
CF
Long Life
Low ESR
Higher Capacitance
CJ
Specifications
Item
Performance Characteristics
Category Temperature Range
– 55 to +105°C
Rated Voltage Range
2.5 to 25V
Rated Capacitance Range 3.3 to 1500µF
± 20%
Capacitance Tolerance
at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
Less than or equal to the specified value.
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C
Z– 55°C / Z+20°C
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
1.25
1.25
(100kHz)
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed
at right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface
shall not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall
be two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall
be once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Resistance to
Soldering Heat
Marking
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 6.3V 150µF)
Dimensions
Positive
Series
φD + 0.5 MAX.
Voltage ( j:6.3v)
1
2
3
4
5
6
7
8
Taping code
9 10 11 12 13 14
φD
PC F 0 J 1 5 1 MC L 1 GS
0.5 MAX.
C±0.2
Code
4 to 6.3 5.5L）
（
GB
5 to 10 L
（
GS
6）
Configuration
A±0.2
B± 0.2
Size code
E
Lot No.
CF
150
j
841
Capacitance
Plastic platform
0.3 MAX.
Capacitance toleranc (±20%)
Rated capacitance (150µF)
L +0.1
- 0.4
Negative
Rated voltage (6.3V)
H
Series name
Type
(mm)
Size
φD
L
A
B
C
E
H
φ4 × 5.5L
φ5 × 6L φ6.3 × 5.5L φ6.3 × 6L φ8 × 7L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L
6.3
10.0
4.0
5.0
6.3
8.0
8.0
10.0
10.0
5.4
12.6
5.4
5.9
5.9
6.9
11.9
7.9
9.9
7.3
11.0
5.0
6.0
7.3
9.0
9.0
11.0
11.0
6.6
10.3
4.3
5.3
6.6
8.3
8.3
10.3
10.3
6.6
10.3
4.3
5.3
6.6
8.3
8.3
10.3
10.3
2.1
4.6
1.0
1.6
2.1
3.2
3.2
4.6
4.6
0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Dimension table in next page.
Voltage
V
2.5
4
6.3
10
16
20
25
Code
e
g
j
A
C
D
E
CAT.8100B
