CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
NPCAP
TM
PSC
-
Radial Lead
Series
●Super
low ESR, high ripple current capability
profile than PSA (φ8×8L to φ10×12.5L)
●Rated voltage range : 2.5 to 16Vdc
●Nominal capacitance range : 270 to 2,700μF
●Endurance : 2,000 hours at 105℃
●Suitable for DC-DC converters, voltage regulators and decoupling applications
for computer motherboards
●Added 2.5V 820µF (ESR 5mΩ max.)
●RoHS Compliant
PSC
●Lower
Low profile
Lower ESR
PSA
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105℃
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
*Note
Rated voltage×1.15
I=0.2CV or 500µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (Vdc)
Dissipation Factor
(tan )
δ
0.10 max.
Low Temperature
Characteristics
(Max.Impedance Ratio)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
2.5 to 16Vdc
±20% (M)
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
≦150% of the initial specified value
D.F. (tan )
δ
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
≦±20% of the initial value
Capacitance change
≦150% of the initial specified value
D.F. (tan )
δ
ESR
≦150% of the initial specified value
≦The initial specified value
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
≦±20% of the initial value
Capacitance change
≦150% of the initial specified value
D.F. (tan )
δ
ESR
≦150% of the initial specified value
≦The initial specified value
Leakage current
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
●Terminal
◆MARKING
Code : E
EX) 2.5V820μF
φD'
φd
F 0.5
Coated Case
L'
15min.
4min.
Size code
H08
φD
8.0
φd
0.6
F
3.5
φD'
L'
L+1.0max.
HB5
JB5
8.0
10.0
0.8(Note1)
0.8(Note1)
3.5
5.0
φD+0.5max.
L+1.5max.
JC5
10.0
0.6
5.0
C 3D6
820
2.5V
Note1 : 0.6 for rated volt 16V.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001M