HOME在庫検索>在庫情報

部品型式

PLF1D121MCL2

製品説明
仕様・特性

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CF Chip Type, Standard series Low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC). CS CG Higher Capacitance, CF Long Life Low ESR Higher Capacitance CJ Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 2.5 to 25V Rated Capacitance Range 3.3 to 1500µF ± 20% Capacitance Tolerance at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( Less than or equal to the specified value at 100kHz, 20°C 1) Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Temperature Characteristics (Max.Impedance Ratio) Z+105°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value 1.25 1.25 (100kHz) After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Navy blue print on the case top Resistance to Soldering Heat Marking 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Type numbering system (Example : 6.3V 150µF) Dimensions Positive Series φD + 0.5 MAX. Voltage ( j:6.3v) 1 2 3 4 5 6 7 8 Taping code 9 10 11 12 13 14 φD PC F 0 J 1 5 1 MC L 1 GS 0.5 MAX. C±0.2 Code 4 to 6.3 5.5L) ( GB 5 to 10 L ( GS 6) Configuration A±0.2 B± 0.2 Size code E Lot No. CF 150 j 841 Capacitance Plastic platform 0.3 MAX. Capacitance toleranc (±20%) Rated capacitance (150µF) L +0.1 - 0.4 Negative Rated voltage (6.3V) H Series name Type (mm) Size φD L A B C E H φ4 × 5.5L φ5 × 6L φ6.3 × 5.5L φ6.3 × 6L φ8 × 7L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 12.7L 6.3 10.0 4.0 5.0 6.3 8.0 8.0 10.0 10.0 5.4 12.6 5.4 5.9 5.9 6.9 11.9 7.9 9.9 7.3 11.0 5.0 6.0 7.3 9.0 9.0 11.0 11.0 6.6 10.3 4.3 5.3 6.6 8.3 8.3 10.3 10.3 6.6 10.3 4.3 5.3 6.6 8.3 8.3 10.3 10.3 2.1 4.6 1.0 1.6 2.1 3.2 3.2 4.6 4.6 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Dimension table in next page. Voltage V 2.5 4 6.3 10 16 20 25 Code e g j A C D E CAT.8100B

ブランド

NICHICON

会社名

ニチコン株式会社

本社国名

日本

事業概要

コンデンサなどの開発、製造、販売している企業である。

供給状況

 
Not pic File
お求めのPLF1D121MCL2は、clevertechのSTAFFが在庫確認を行いメールにて御回答致します。

「見積依頼」ボタンを押してお気軽にお進み下さい。


当サイトの取引の流れ

見積依頼→在庫確認→見積回答→注文→検収→支払 となります。


お取引内容はこちら
PLF1D121MCL2の取扱い販売会社 株式会社クレバーテック  会社情報(PDF)    戻る


0.0700979233