CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
NPCAP
TM
PXE
-
Surface Mount
Series
PXF
●Super
low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
●Rated voltage range : 2.5 to 16Vdc, Capacitance range : 33 to 2,700µF
●Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
●RoHS Compliant
●Halogen Free
Lower ESR
PXE
Lower ESR
PXA
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tan
δ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
-55 to +105℃
2.5 to 16Vdc
±20% (M)
Rated voltage×1.15
Shall not exceed values shown in STANDARD RATINGS.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.12 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
DF (tanδ)
≦150% of the initial specified value
≦150% of the initial specified value
ESR
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
DF (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
≦The initial specified value
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
DF (tanδ)
≦150% of the initial specified value
≦150% of the initial specified value
ESR
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆MARKING
◆DIMENSIONS [mm]
● Terminal
Size Code
E61
F61
F80
H70
H80
HA0
HC0
J80
JA0
JC0
Code : A
P
C±0.2
B±0.2
φD±0.5
W
0.3max.
L±0.3 (Note)
A±0.2
(Note) L±0.5 for HA0, HC0, JA0, JC0
φD
5
6.3
6.3
8
8
8
8
10
10
10
A
B
C
L
5.8 5.3 5.3 5.9
5.8 6.6 6.6 7.2
7.7 6.6 6.6 7.2
6.7 8.3 8.3 9.0
7.7 8.3 8.3 9.0
10.0 8.3 8.3 9.0
12.0 8.3 8.3 9.0
7.7 10.3 10.3 11.0
10.0 10.3 10.3 11.0
12.2 10.3 10.3 11.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.4
1.9
1.9
3.1
3.1
3.1
3.1
4.5
4.5
4.5
EX) 2.5V390µF
E49A
390
2.5V
◆PART NUMBERING SYSTEM
1
2
3
4
A PXE
5
6
7
8
9
10
A RA
11
12
13
14
M
15
16
17
18
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 47μF:470,100μF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001M
