Engineering Bulletin
Standard, 105C
Aluminum Electrolytic Capacitors
No.511P / Oct.2004
@Endurance with ripple current : 105C 1000 hours
@Solvent-proof type except 350 to 400Vdc
@Pb-free design
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
-55 to +105C(6.3 to 100Vdc) -40 to +105C(160 to 400Vdc)
Rated Voltage Range
Capacitance Tolerance
Leakage Current
6.3 to 400Vdc
P20% (M)
6.3 to 100Vdc
I=0.03CV or 4MA, whichever is greater.
I=0.01CV or 3MA, whichever is greater.
(at 20C, 120Hz)
160 to 400Vdc
Time After 1minute
(at 20C after 1 minute) CV
(at 20C after 2 minutes) CV[1000 I=0.1CV+40 max.
CV>1000 I=0.04CV+100 max.
After 5minutes
I=0.03CV+15 max.
I=0.02CV+25 max.
(at 20C)
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V
tanE (Max.)
0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08
0.20
0.24
When nominal capacitance exceeds 1000MF, add 0.02 to the value above for each 1000MF increase.
(at 20C, 120Hz)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V
Z(-25C)/Z(+20C)
6
3
2
2
2
2
2
2
3
4
Z(-40C)/Z(+20C)
(at 120Hz)
6
4
3
3
3
3
3
4
6
8
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with the rated ripple
current is applied for 1000 hours at 105C.
Capacitance change
[P20% of the initial value
D.F. (tanE)
[200% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1000 hours at 105C
without voltage applied.
Rated voltage
6.3 to 100Vdc
160 to 400Vdc
Capacitance change
[P20% of the initial value
[P20% of the initial value
D.F. (tanE)
[200% of the initial specified value [200% of the initial specified value
Leakage current
[The initial specified value
[500% of the initial specified value
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
?DIMENSIONS [mm]
FP0.5
FD'
Fd
Sleeve (PET)
FP0.5
@Terminal Code : E
L'
15min.
4min.
Vent
(except F5)
(F5 to F10)
(F12.5 to F18)
fD
fd
F
fD'
L'
5
0.5
2.0
6.3
0.5
2.5
10 12.5
8
0.6 0.6 0.6
3.5 5.0 5.0
FD+0.5max.
L+1.5max
16
0.8
7.5
18
0.8
7.5
Gas escape end seal
?PART NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
E KME A A A E A A A A A M A A A N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 0.1MF:R10,10MF:100,100MF:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,35V:350,400V:401)
Series code
Category
Specifications in this bulletin are subject to change without notice.
NIPPON CHEMI-CON CORPORATION
1232
1
