Features
• Serial Peripheral Interface (SPI) Compatible
• Supports SPI Modes 0 (0,0) and 3 (1,1)
– Data Sheet Describes Mode 0 Operation
• Low-voltage and Standard-voltage Operation
•
•
•
•
•
•
•
•
•
– 2.7 (VCC = 2.7V to 5.5V)
– 1.8 (VCC = 1.8V to 5.5V)
20 MHz Clock Rate (5V)
8-byte Page Mode
Block Write Protection
– Protect 1/4, 1/2, or Entire Array
Write Protect (WP) Pin and Write Disable Instructions for Both Hardware and Software
Data Protection
Self-timed Write Cycle (5 ms max)
High Reliability
– Endurance: One Million Write Cycles
– Data Retention: 100 Years
Automotive Devices Available
8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin mini-MAP (MLP 2x3) and 8lead TSSOP Packages
Die Sales: Wafer Form, Waffle Pack, Bumped Wafers
Description
The AT25010A/020A/040A provides 1024/2048/4096 bits of serial electrically erasable programmable read-only memory (EEPROM) organized as 128/256/512 words of
8 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The
AT25010A/020A/040A is available in space saving 8-lead PDIP, 8-lead JEDEC SOIC,
8-lead Ultra Thin mini-MAP (MLP 2x3), and 8-lead TSSOP packages.
The AT25010A/020A/040A is enabled through the Chip Select pin (CS) and accessed
via a three-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO),
and Serial Clock (SCK). All programming cycles are completely self-timed, and no
separate erase cycle is required before write.
Block write protection is enabled by programming the status register with one of four
blocks of write protection. Separate Program Enable and Program disable instructions
are provided for additional data protection. Hardware data protection is provided via
the WP pin to protect against inadvertent write attempts. The HOLD pin may be used
to suspend any serial communication without resetting the serial sequence.
Table 1. Pin Configuration
Pin Name
Chip Select
SCK
Serial Data Clock
SI
Serial Data Output
GND
Ground
VCC
Power Supply
WP
Write Protect
HOLD
Suspends Serial Input
2K (256x8)
4K (512x8)
AT25010A
AT25020A
AT25040A
Not
Recommended
for New Design
Serial Data Input
SO
1K (128x8)
8-lead SOIC
8-lead PDIP
Function
CS
SPI Serial
EEPROM
CS
SO
WP
GND
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
C S
SO
W P
G N D
8-lead Ultra Thin mini-MAP (MLP 2x3)
VCC
HOLD
SCK
SI
8
7
6
5
1
2
3
4
CS
SO
WP
GND
1
2
3
4
8
7
6
5
V
H
S
S
C C
O L
C K
I
V
H
S
S
C C
O L
C K
I
8-lead TSSOP
C S
SO
W P
G N D
1
2
3
4
8
7
6
5
Bottom view
3348J–SEEPR–8/06
AT25010A/020A/040A
Table 2. Pin Capacitance (1)
Applicable over recommended operating range from TA = 25°C, f = 1.0 MHz, VCC = +5.0V (unless otherwise noted)
Symbol
Test Conditions
COUT
Units
Output Capacitance (SO)
8
pF
VOUT = 0V
Input Capacitance (CS, SCK, SI, WP, HOLD)
CIN
Note:
Max
Conditions
6
pF
VIN = 0V
1. This parameter is characterized and is not 100% tested.
Table 3. DC Characteristics(1)
Applicable over recommended operating range from: TAI = 40C to +85C, VCC = +1.8V to +5.5V, (unless otherwise noted)
Symbol
Parameter
VCC1
Supply Voltage
VCC2
Max
Units
1.8
5.5
V
Supply Voltage
2.7
5.5
V
VCC3
Supply Voltage
4.5
5.5
V
ICC1
Supply Current
VCC = 5.0V at 20 MHz, SO = Open, Read
8.5
10.0
mA
ICC2
Supply Current
VCC = 5.0V at 10 MHz, SO = Open, Read, Write
4.5
5.0
mA
ICC3
Supply Current
VCC = 5.0V at 1 MHz, SO = Open, Read, Write
2.0
3.0
mA
ISB1
Standby Current
VCC = 1.8V, CS = VCC
0.1
0.5
µA
ISB2
Standby Current
VCC = 2.7V, CS = VCC
0.2
1.0
µA
ISB3
Standby Current
VCC = 5.0V, CS = VCC
2.0
3.5
µA
IIL
Input Leakage
VIN = 0V to VCC
3.0
Output Leakage
VIN = 0V to VCC, TAC = 0°C to 70°C
3.0
3.0
µA
Input Low-voltage
0.6
VCC x
0.3
V
VIH(1)
Input High-voltage
VCC x 0.7
VCC +
0.5
V
VOL1
Output Low-voltage
0.4
V
VOH1
Output High-voltage
VOL2
Output Low-voltage
VOH2
Output High-voltage
IOL
VIL
(1)
Note:
Test Condition
3.6V VCC 5.5V
1.8V VCC 3.6V
Min
IOL = 3.0 mA
IOH = 1.6 mA
µA
VCC 0.8
IOL = 0.15 mA
IOH = 100 µA
Typ
V
0.2
VCC 0.2
V
V
1. VIL min and VIH max are reference only and are not tested.
3
3348J–SEEPR–8/06
