ALUMINUM ELECTROLYTIC CAPACITORS
ZS
4.5mmL Chip Type
series
WX
Chip type with 4.5mm height.
Designed for surface mounting on high density PC board.
Smaller
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
ZS
High
Te m p e rature
ZT
ZP
Bi-polarized
Smaller
Specifications
ZR
Item
Performance Characteristics
Category Temperature Range
– 40 to + 85°C
Rated Voltage Range
4 to 50V
Rated Capacitance Range
0.1 to 220µF
Capacitance Tolerance
+ 20% at 120Hz, 20°C
–
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) ,whichever is greater.
Leakage Current
Measurement frequency : 120Hz at 20°C
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
4
0.50
6.3
0.30
10
0.24
16
0.19
25
0.16
35
0.14
50
0.14
Measurement frequency : 120Hz
4
7
15
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
Stability at Low Temperature
6.3
4
8
16
2
4
35
2
3
50
2
3
Within + 20% of the initial capacitance value
–
200% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within + 10% of the initial capacitance value
–
maintained at 250°C. The capacitors shall meet the
tan δ
Less than or equal to the initial specified value
characteristic requirements listed at right when they are
Leakage current
Less than or equal to the initial specified value
removed from the plate and restored to 20°C.
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Type numbering system (Example : 16V 10µF)
Chip Type
1
4.5
Voltage mark for 6.3V is
C + 0.2
–
3
4
5
6
7
8
9 10 11 12 13 14
Taping code
E
B+ 0.2
–
A2
10
16V
φD+ 0.5
–
Voltage
2
U Z S 1 C 1 0 0 MC L 1 GB
A+ 0.3 A + 0.3
–
–
Plastic platform
0.3 MAX.
0.5 MAX.
Positive
Capacitance
Lot No.
25
2
4
Capacitance change
tan δ
Leakage current
The specifications listed at right shall be met when
the capacitors are restored to 20°C after the rated
voltage is applied for 2000 hours at 85°C.
Endurance
10
3
8
φD
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
(mm)
6.3
2.4
6.6
6.6
2.2
Configuration
Capacitance tolerance (+ 20%)
–
Rated capacitance (10µF)
Rated voltage (16V)
+ 0.1
– 0.2
Series name
Negative
0.5 to 0.8
6V .
Type
Dimensions
4
0G
V
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
220
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
221
4
4
5
6.3
6.3
0J
28
33
56
96
4
5
5
6.3
10
1A
28
37
45
70
5
5
6.3
16
1C
33
41
52
4
5
6.3
6.3
25
1E
23
37
49
58
4
5
6.3
6.3
35
1V
16
27
42
52
4
5
6.3
50
1H
18
29
46
4
4
4
4
4
4
4
5
6.3
Case size
φ D (mm)
1.0
2.0
2.8
4.0
8.4
13
17
20
33
Rated
ripple
Rated ripple current (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please select UR(p.106), UG(p.114) series if high C/V
products are reqired.
Please refer to page 3 for the minimum order quantity.
CAT.8100B
