ALUMINUM ELECTROLYTIC CAPACITORS
ZE
3.95mmL MAX. Chip Type, Bi-polarized
series
Chip type with 3.95mmL MAX, height.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
ZP
Smaller
ZE
Specifications
Item
Performance Characteristics
Category Temperature Range
– 40 to +85°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range
0.1 to 47µF
Capacitance Tolerance
±20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.05 CV or 10 (µA) , whichever is greater.
Measurement frequency : 120Hz at 20°C
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
6.3
0.30
10
0.24
16
0.20
25
0.18
35
0.16
50
0.16
Measurement frequency : 120Hz
6.3
4
8
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
Z– 40°C / Z+20°C
Stability at Low Temperature
10
3
8
16
2
4
25
2
4
35
2
3
50
2
3
The specifications listed at right shall be met when
Capacitance change
Within ±30% of the initial capacitance value
the capacitors are restored to 20°C after the rated
tan δ
300% or less than the initial specified value
voltage is applied for 1000 hours at 85°C with the
Leakage current
Less than or equal to the initial specified value
polarity inverted every 250 hours.
After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which
Capacitance change Within ±10% of the initial capacitance value
is maintained at 250°C. The capacitors shall meet the
tan δ
Less than or equal to the initial specified value
characteristic requirements listed at right when they are
Leakage current
Less than or equal to the initial specified value
removed from the plate and restored to 20°C.
Endurance
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Type numbering system (Example : 16V 10µF)
Plastic platform
0.3 MAX.
Series
C±0.2
A±0.3
Capacitance
1
3.90 +0.05
–0.2
0.5 to 0.8
Voltage
V
6.3
10
16
25
35
j
A
C
E
V
3
4
5
6
7
8
9 10 11 12 13 14
Taping code
φD
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
Configuration
(mm)
6.3
2.4
6.6
6.6
2.2
Capacitance tolerance (±20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
50
Code
2
U Z E 1 C 1 0 0 MC L 1 GB
E
B±0.2
A2
10C
ZE
φD±0.5
Lot No.
A±0.3
Voltage (C : 16V)
0.5 MAX.
Chip Type
H
Type
Dimensions
6.3
0J
V
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
5
6.3
6.3
10
1A
28
37
45
4
6.3
6.3
16
1C
17
33
41
4
5
6.3
6.3
25
1E
12
23
37
49
5
5
6.3
35
1V
12
16
27
4
5
5
6.3
50
1H
8.4
16
18
29
4
4
4
4
4
5
5
6.3
Case size
φ D (mm)
1.0
2.0
2.8
4.0
8.4
13
17
20
Rated
ripple
Rated ripple current (mArms) at 85°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size soldering by reflow are given
in page 18,19.
Please refer to page 3 for the minimum order quantity.
CAT.8100B
