DECOUPLING DEVICE FOR HIGH FREQUENCY
F11
Higher Capacitance.
Low ESR, Low ESL,High ripple current.
Resin-molded Chip.
Designed for surface mounting on high density PC board.
Load life of 5000 hours at +105°C.
Compliant to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category Temperature Range −55 to +105°C
Capacitance Tolerance ±20% (at 120Hz)
Dissipation Factor
Refer to next table
ESR
Refer to next table
Leakage Current
After 5 minute’s application of rated voltage,
leakage current is not more than 0.1CV
At 60°C 90%RH 500hours (No voltage applied)
Capacitance Change..Within −20 to +30% of the initial specified value
Dissipation Factor.......200% or less than the Initial specified value
ESR............................200% or less than the Initial specified value
Leakage Current.........Initial specified value or less
Damp Heat
(Steady State)
−55°C / +105°C 30minutes each 5cycle
Capacitance Change..Within ±20% of the Initial specified value
Dissipation Factor.......200% or less than the Initial specified value
ESR ............................200% or less than the Initial specified value
Leakage Current.........Initial specified value or less
Temperature Cycles
Type numbering system (Example : 2.5V 220µF)
1
2
3
4
5
6
7
8
9
10
11
12 13 14
F 1 1 0 E 2 2 7 M D L AH
Low ESR
−55°C
Temperature Change Capacitance Change
Dissipation Factor
Characteristics
ESR
Leakage Current
Taping code
code
Tape width
(mm)
L
16
φ180
24
φ330
Resistance
to Soldering Heat
Capacitance Change..Within ±20% of the Initial specified value
Dissipation Factor.......Initial specified value or less
ESR............................Initial specified value or less
Leakage Current.........Initial specified value or less
Case code
Capacitance tolerance
Rated capacitance
After application of 115% of rating voltage at the rate of
30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 105°C, capacitors meet the characteristics
requirements listed below.
Rated voltage
Series
Surge
Capacitance Change....Within ±20% of the initial specified value
Dissipation Factor.........200% or less than the Initial specified value
ESR ..............................200% or less than the Initial specified value
Leakage Current...........Initial specified value or less
Dimensions
After 5000 hours’ application of rated voltage at 105°C, they will meet
the specified value for life charecteristics listed below.
L1
W2
Capacitance Change....Within ±20% of the initial value
Dissipation Factor.........200% or less than the Initial specified value
ESR ..............................200% or less than the Initial specified value
Leakage Current...........Initial specified value or less
Endurance
W1
H
Printed on the package top.
Marking
P
S2
S1
Within −0 to +50%
150% or less than the Initial specified value
150% or less than the Initial specified value
10 times Initial specified value
Capacitor meets the following characteristics after solder reflow
(Peak: 240°C for 10sec, 2cycle).
Temperature should be measured at the terminals.
Reel Dia
(mm)
K
+105°C
Within −20 to +0%
Initial specified value or less
Initial specified value or less
Initial specified value or less
S3
L2
(mm)
Case Code
W1
L2
W2
D
L1
8.5 ± 0.2
7.3 ± 0.2
5.3 ± 0.2
1.7 ± 0.2
H
2.0MAX.
F
16.7 ± 0.2 15.6 ± 0.2
12.1 ± 0.2
3.6 ± 0.2
2.5MAX.
Marking
S1
0.9 ± 0.2
S2
0.6 ± 0.2
S3
0.5 ± 0.2
P
3.3 ± 0.2
1.5 ± 0.1
1.3 ± 0.1
1.5 ± 0.2
7.0 ± 0.2
Standard ratings
V
Seriese
F case only
F11
0E128M
8J1234
Rated Voltage
(Voltage code)
Capacitance Tolerance
Rated Capacitance
(Capacitance code)
Lot No.
Cap.(µF)
47
100
220
330
600
800
1200
Code
476
107
227
337
607
807
128
2.5
0E
D
D
(D)
F
4
0G
D
D
(D)
6.3
0J
D
(D)
F
F
F
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
CAT.8100Y
