PIC18F6520/8520/6620/
8620/6720/8720
64/80-Pin High-Performance, 256 Kbit to 1 Mbit
Enhanced Flash Microcontrollers with A/D
High-Performance RISC CPU:
Analog Features:
• C compiler optimized architecture/instruction set:
- Source code compatible with the PIC16 and
PIC17 instruction sets
• Linear program memory addressing to 128 Kbytes
• Linear data memory addressing to 3840 bytes
• 1 Kbyte of data EEPROM
• Up to 10 MIPs operation:
- DC – 40 MHz osc./clock input
- 4 MHz – 10 MHz osc./clock input with PLL active
• 16-bit wide instructions, 8-bit wide data path
• Priority levels for interrupts
• 31-level, software accessible hardware stack
• 8 x 8 Single Cycle Hardware Multiplier
• 10-bit, up to 16-channel Analog-to-Digital
Converter (A/D):
- Conversion available during Sleep
• Programmable 16-level Low-Voltage Detection
(LVD) module:
- Supports interrupt on Low-Voltage Detection
• Programmable Brown-out Reset (PBOR)
• Dual analog comparators:
- Programmable input/output configuration
Special Microcontroller Features:
• 100,000 erase/write cycle Enhanced Flash
program memory typical
• 1,000,000 erase/write cycle Data EEPROM
memory typical
• 1 second programming time
• Flash/Data EEPROM Retention: > 40 years
• Self-reprogrammable under software control
• Power-on Reset (POR), Power-up Timer (PWRT)
and Oscillator Start-up Timer (OST)
• Watchdog Timer (WDT) with its own On-Chip
RC Oscillator for reliable operation
• Programmable code protection
• Power saving Sleep mode
• Selectable oscillator options including:
- 4X Phase Lock Loop (of primary oscillator)
- Secondary Oscillator (32 kHz) clock input
• In-Circuit Serial Programming™ (ICSP™) via
two pins
• MPLAB® In-Circuit Debug (ICD) via two pins
External Memory Interface
(PIC18F8X20 Devices Only):
• Address capability of up to 2 Mbytes
• 16-bit interface
Peripheral Features:
•
•
•
•
•
•
•
•
•
High current sink/source 25 mA/25 mA
Four external interrupt pins
Timer0 module: 8-bit/16-bit timer/counter
Timer1 module: 16-bit timer/counter
Timer2 module: 8-bit timer/counter
Timer3 module: 16-bit timer/counter
Timer4 module: 8-bit timer/counter
Secondary oscillator clock option – Timer1/Timer3
Five Capture/Compare/PWM (CCP) modules:
- Capture is 16-bit, max. resolution 6.25 ns (TCY/16)
- Compare is 16-bit, max. resolution 100 ns (TCY)
- PWM output: PWM resolution is 1 to 10-bit
• Master Synchronous Serial Port (MSSP) module
with two modes of operation:
- 3-wire SPI (supports all 4 SPI modes)
- I2C™ Master and Slave mode
• Two Addressable USART modules:
- Supports RS-485 and RS-232
• Parallel Slave Port (PSP) module
Program Memory
Device
CMOS Technology:
•
•
•
•
Data Memory
# Single-Word SRAM EEPROM I/O
Bytes
Instructions (bytes) (bytes)
Low-power, high-speed Flash technology
Fully static design
Wide operating voltage range (2.0V to 5.5V)
Industrial and Extended temperature ranges
10-bit
CCP
A/D
(PWM)
(ch)
MSSP
Max
Timers
Ext
USART
FOSC
Master
8-bit/16-bit Bus
SPI
(MHz)
I2C
PIC18F6520
32K
16384
2048
1024
52
12
5
Y
Y
2
2/3
N
PIC18F6620
64K
32768
3840
1024
52
12
5
Y
Y
2
2/3
N
25
PIC18F6720 128K
65536
3840
1024
52
12
5
Y
Y
2
2/3
N
25
PIC18F8520
32K
16384
2048
1024
68
16
5
Y
Y
2
2/3
Y
40
PIC18F8620
64K
32768
3840
1024
68
16
5
Y
Y
2
2/3
Y
25
PIC18F8720 128K
65536
3840
1024
68
16
5
Y
Y
2
2/3
Y
25
2003-2013 Microchip Technology Inc.
40
DS39609C-page 1