HOME＞在庫検索＞在庫情報
HV0E107N
Super Capacitor HV Series Dimensions H L min. ͬL min. P±0.1 φ D±0.5 Negative polarity φd Anode polarity Markings 2.7V 10F SuperCapacitor HV Standard Rating Part No. HV0E106N HV0E226N HV0E506N HV0E107N Max. Rated Voltage (Vdc) 2.7 2.7 2.7 2.7 Nominal Capacitance (F) 10 22 50 100 Max. ESR (at 1 kHz) (m⏲) 500 500 100 100 Max. Current at 30 minutes (mA) 8 18 40 80 Dimensions (Unit: mm) D 10.0 12.5 18.0 22.0 35±2 35±2 40±5 50±5 P d l ͬL Weight (g) 5.0 5.0 7.5 10.2 0.6 0.6 0.8 1.0 15.0 15.0 15.0 18.0 5.0 5.0 5.0 7.0 4.5 6.5 14.0 24.0 H Specifications Item Operating Temperature Range Maximum Operating Voltage Nominal Capacitance Range Capacitance Allowance Equivalent Series Resistance (ESR) Current at 30 minutes Phase 2 Tempere Variation of Characteristics Phase 4 Phase 5 Lead Strength (Tensile) Vibration Resistance Solderability Soldering Heat Resistance Temperature Cycle Humidity Resistance High Temperature Load Life Specification –25˚C to +60˚C 2.7 Vdc 10F to 100F ±30% See Standard list See Standard list Capacitance More than 50% of initial value ESR Not to exceed 4 times initial value Capacitance Not to exceed 150% of initial value ESR Not to exceed initial requirement Current at 30minutes Not to exceed 1.5CV(mA) ͬC/C Within ±20% of initial value ESR Not to exceed initial requirement Current at 30 minutes Not to exceed initial requirement No loosening nor permanent damage of the leads Caoacitance ESR Meet initial standard value Current at 30 minutes Appearance Noobvious abnormality 3/4 or more of the pin surface should be covered with new solder Capacitance ESR Current at 30 minutes Appearance Capacitance ESR Current at 30 minutes Appearance Capacitance ESR Current at 30 minutes Appearance Capacitance ESR Current at 30 minutes Appearance Should satisfy initial standard value No obvious abnormality Meet initial standard value No obvious abnormality Within ±20% of initial value 1.2 or less time initial standard value 1.2 or less time initial standard value No obvious abnormality Within ±30% of initial value Twice or less times initial standard value Twice or less times initial standard value No obvious abnormality Test Conditions Conforming to JIS C 5102–1994 Conforms to 7.12 Phase2: –25±2˚C Phase4: +60±2˚C Phase5: +25±2˚C Conforms to 8.1.2 (1) Conforms to 8.2.3 (1) Frequency: 10 to 55Hz Test duration: 6 hours Conforms to 8.4 Solder temperature: 230±5˚C Dipping duration: 5±0.5sec. Shold be dipped up to 1.6mm from the lower end of the capacitor Conforms to 8.5 Solder temperature: 260±10˚C Dipping duration: 10±1sec. Shold be dipped up to 1.6mm from the lower end of the capacitor Conforms to 9.3 Temperature: –25˚CǞR.T.Ǟ+60˚CǞR.T. Number of cycles: 5 cycles Conforms 9.5 Temperature: 40±2˚C Relative humidity: 90 to 95% RH Test duration: 240±8hours Conforms 9.10 Temperature: 60±2˚C Voltage applied: 2.7Vdc Test duration: 1000+48 hours –0 Series protection resistance: 0⏲ Super Capacitors Vol.05 89
弊社からの見積回答メールの返信又はFAXにてお願いします。
