CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
NPCAP
TM
PXA
-
● Super
Surface Mount
Series
low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
● Rated voltage range : 2.5 to 25Vdc, case size range : φ4×5.2L toφ10×12.2L
● Suitable for DC-DC converters, voltage regulators and decoupling applications used on
computer motherboards etc.
●RoHS Compliant
●Halogen Free
PXE
Lower ESR
PXA
◆SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
-55 to +105℃
2.5 to 25Vdc
±20% (M)
Rated voltage×1.15 (Rated voltage 2.5 to 20Vdc, 25Vdc) / Rated voltage×1.00 (Rated voltage 23Vdc)
Shall not exceed values shown in STANDARD RATINGS.
0.12 max.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
(F46 : 1,000 hours) at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
≦150% of the initial specified value
DF (tanδ
)
≦150% of the initial specified value
ESR
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at
60℃, 90 to 95% RH for 1,000 hours(F46 : 500 hours).
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
≦150% of the initial specified value
DF (tanδ
)
ESR
≦150% of the initial specified value
≦The initial specified value
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
DF (tanδ
)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
Code : A
◆MARKING
Size code
D55
E60
F46
F55
F60
H70
HC0
J80
JC0
W
P
C±0.2
B±0.2
φD±0.5
●Terminal
0.3max.
A±0.2
L±0.3 (Note)
Note : L+0.1/-0.2 for F46
L±0.5 for HC0 and JC0
φD
4
5
6.3
6.3
6.3
8
8
10
10
L
A
B
C
5.2 4.3 4.3 5.1
5.7 5.3 5.3 5.9
4.5 6.6 6.6 7.2
5.2 6.6 6.6 7.2
5.7 6.6 6.6 7.2
6.7 8.3 8.3 9.0
12.0 8.3 8.3 9.0
7.7 10.3 10.3 11.0
12.2 10.3 10.3 11.0
W
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.0
1.4
1.9
1.9
1.9
3.1
3.1
4.5
4.5
EX) 16V39µF
A15L
39
16V
◆PART NUMBERING SYSTEM
1
2
3
4
A PXA
5
6
7
8
9
10
A RA
11
12
13
14
M
15
16
17
18
G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 10μF:100,100μF:101)
Taping code
Terminal code
Voltage code (ex. 6.3V:6R3,10V:100)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
(1/2)
CAT. No. E1001M
