PIC32MX5XX/6XX/7XX
32-bit Microcontrollers (up to 512 KB Flash and 128 KB SRAM)
with Graphics Interface, USB, CAN, and Ethernet
Operating Conditions
Timers/Output Compare/Input Capture
• 2.3V to 3.6V, -40ºC to +105ºC, DC to 80 MHz
®
Core: 80 MHz/105 DMIPS MIPS32 M4K
• Five General Purpose Timers:
- Five 16-bit and up to two 32-bit Timers/Counters
• Five Output Compare (OC) modules
• Five Input Capture (IC) modules
• Real-Time Clock and Calendar (RTCC) module
®
• MIPS16e® mode for up to 40% smaller code size
• Code-efficient (C and Assembly) architecture
• Single-cycle (MAC) 32x16 and two-cycle 32x32 multiply
Communication Interfaces
Clock Management
•
•
•
•
•
• USB 2.0-compliant Full-Speed OTG controller
• 10/100 Mbps Ethernet MAC with MII and RMII interface
• CAN module:
- 2.0B Active with DeviceNet™ addressing support
• Six UART modules (20 Mbps):
- Supports LIN 2.1 protocols and IrDA® support
• Up to four 4-wire SPI modules (25 Mbps)
• Up to five I2C modules (up to 1 Mbaud) with SMBus
support
• Parallel Master Port (PMP)
0.9% internal oscillator (on some variants)
Programmable PLLs and oscillator clock sources
Fail-Safe Clock Monitor (FSCM)
Independent Watchdog Timer
Fast wake-up and start-up
Power Management
•
•
•
•
Low-power management modes (Sleep and Idle)
Integrated Power-on Reset, Brown-out Reset
0.5 mA/MHz dynamic current (typical)
41 µA IPD current (typical)
Direct Memory Access (DMA)
• Up to eight channels of hardware DMA with automatic
data size detection
• 32-bit Programmable Cyclic Redundancy Check (CRC)
• Six additional channels dedicated to USB, Ethernet and
CAN modules
Graphics Features
• External graphics interface with up to 34 Parallel Master
Port (PMP) pins:
- Interface to external graphics controller
- Capable of driving LCD directly with DMA and
internal or external memory
Input/Output
• 15 mA or 10 mA source/sink for standard VOH/VOL and
up to 22 mA for non-standard VOH1
• 5V-tolerant pins
• Selectable open drain and pull-ups
• External interrupts
Analog Features
• ADC Module:
- 10-bit 1 Msps rate with one Sample and Hold (S&H)
- 16 analog inputs
- Can operate during Sleep mode
• Flexible and independent ADC trigger sources
• Comparators:
- Two dual-input Comparator modules
- Programmable references with 32 voltage points
Qualification and Class B Support
• AEC-Q100 REVH (Grade 2 -40ºC to +105ºC)
• Class B Safety Library, IEC 60730
Debugger Development Support
•
•
•
•
In-circuit and in-application programming
4-wire MIPS® Enhanced JTAG interface
Unlimited program and six complex data breakpoints
IEEE 1149.2-compatible (JTAG) boundary scan
Packages
Type
QFN
TFBGA
VTLA
Pin Count
I/O Pins (up to)
64
51
64
51
100
83
100
83
121
83
124
83
Contact/Lead Pitch
Dimensions
0.50
9x9x0.9
0.50
10x10x1
0.40
12x12x1
0.50
14x14x1
0.80
10x10x1.1
0.50
9x9x0.9
Note:
TQFP
All dimensions are in millimeters (mm) unless specified.
2009-2016 Microchip Technology Inc.
DS60001156J-page 1