IDT54/74FCT162245T/AT/CT
FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
FAST CMOS 16-BIT
BIDIRECTIONAL
TRANSCEIVER
IDT54/74FCT162245T/AT/CT
FEATURES:
DESCRIPTION:
•
•
•
•
•
The FCT162245T 16-bit transceiver is built using advanced dual metal
CMOS technology. These high-speed, low-power transceivers are ideal for
synchronous communication between two buses (A and B). The Direction and
Output Enable controls operate these devices as either two independent 8-bit
transceivers or one 16-bit transceiver. The direction control pin (xDIR) controls
the direction of data flow. The output enable pin (xOE) overrides the direction
control and disables both ports. All inputs are designed with hysteresis for
improved noise margin.
The FCT162245T has balanced output drive with current limiting resistors.
This offers low ground bounce, minimal undershoot, and controlled output fall
times–reducing the need for external series terminating resistors. The
FCT162245T is a plug-in replacement for the FCT16245T and ABT16245 for
on-board interface applications.
•
•
•
•
0.5 MICRON CMOS Technology
High-speed, low-power CMOS replacement for ABT functions
Typical tSK(o) (Output Skew) < 250ps
Low input and output leakage ≤ 1µA (max.)
ESD > 2000V per MIL-STD-883, Method 3015; > 200V using
machine model (C = 200pF, R = 0)
Balanced Output Drivers:
– ±24mA (industrial)
– ±16mA (military)
Reduced system switching noise
Typical VOLP (Output Ground Bounce) < 0.6V at VCC = 5V,
TA = 25°C
Available in the following packages:
– Industrial: SSOP, TSSOP
– Military: CERPACK
FUNCTIONAL BLOCK DIAGRAM
1 DIR
2 DIR
1OE
2OE
1A1
2A1
1B1
2B1
1A2
2A2
1B2
2B2
1A3
2A3
1B3
2B3
1A4
2A4
1B4
2B4
1A5
2A5
1B5
2B5
1A6
2A6
1B6
2B6
1A7
2A7
1B7
2B7
1A8
2A8
1B8
2B8
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
SEPTEMBER 2009
1
© 2009 Integrated Device Technology, Inc.
DSC-5457/8
IDT54/74FCT162245T/AT/CT
FAST CMOS 16-BIT BIDIRECTIONAL TRANSCEIVER
MILITARY AND INDUSTRIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 5.0V ±10%; Military: TA = –55°C to +125°C, VCC = 5.0V ±10%
Symbol
Test Conditions(1)
Parameter
Min.
Typ.(2)
Max.
Unit
VIH
Input HIGH Level
Guaranteed Logic HIGH Level
2
—
—
V
VIL
Input LOW Level
Guaranteed Logic LOW Level
—
—
0.8
V
IIH
Input HIGH Current (Input pins)(5)
VCC = Max.
—
—
±1
µA
—
—
±1
—
—
±1
—
—
±1
VO = 2.7V
—
—
±1
VO = 0.5V
—
—
±1
—
–0.7
–1.2
V
–80
–140
–250
mA
—
100
—
mV
—
5
500
µA
Min.
60
–60
2.4
Typ.(2)
115
–115
3.3
Max.
200
–200
—
Unit
mA
mA
V
—
0.3
0.55
V
VI = VCC
Input HIGH Current (I/O pins)(5)
IIL
Input LOW Current (Input pins)(5)
VI = GND
Input LOW Current (I/O pins)(5)
IOZH
High Impedance Output Current
IOZL
(3-State Output pins)(5)
VIK
Clamp Diode Voltage
IOS
Short Circuit Current
VH
Quiescent Power Supply Current
VCC = Min., IIN = –18mA
VCC = Max., VO =
GND(3)
Input Hysteresis
ICCL
ICCH
ICCZ
VCC = Max.
—
VCC = Max.
VIN = GND or VCC
µA
µA
OUTPUT DRIVE CHARACTERISTICS
Symbol
IODL
IODH
VOH
VOL
Parameter
Output LOW Current
Output HIGH Current
Output HIGH Voltage
Output LOW Voltage
Test Conditions(1)
VCC = 5V, VIN = VIH or VIL, VO = 1.5V(3)
VCC = 5V, VIN = VIH or VIL, VO = 1.5V(3)
VCC = Min
IOH = –16mA MIL
VIN = VIH or VIL
IOH = –24mA IND
VCC = Min
IOH = 16mA MIL
VIN = VIH or VIL
IOH = 24mA IND
NOTES:
1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. Duration of the condition can not exceed one second.
5. This test limit for this parameter is ±5µA at TA = –55°C.
3
