LC01-6
Bidirectional TVS Array ™
SCOTTSDALE DIVISION
DESCRIPTION
WWW . Microsemi .C OM
TVSARRAY™
This 16 pin one-line pair, bidirectional, LOW CAPACITANCE array is designed for
use in applications where protection is required at the board level. The SO-16W
package design provides protection from voltage transients caused by electrostatic
discharge (ESD) as defined in IEC 61000-4-2, electrical fast transients (EFT) per
IEC 61000-4-4 and effects of secondary lightning as stated by IEC 61000-4-5.
These TRANSIENT VOLTAGE SUPPRESSOR (TVS) arrays have a peak pulse
power rating of 1500 watts for a 10/1000 µsec pulse and are designed to be used for
secondary surge protection on high-speed telecommunications lines. This device
can be used in either common or differential mode applications. It is typically used
between Tip and Ring. Applications include T1/E1 and DSL interfaces in base
stations, routers, and long-haul transient immunity requirement per Bellcore 1089,
FCC Part 68 (type A and B surges and IEC 61000-4-5
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
FEATURES
•
•
•
•
•
•
APPLICATIONS / BENEFITS
•
•
•
•
•
•
1500 watts peak pulse power
Protects one-line pair
Provides electrically isolated protection
SO-16W package
UL 94V-0 flamability classification
LOW CAPACITANCE 50 pF per line pair
MAXIMUM RATINGS
•
•
•
•
•
•
T1/E1 line cards
Base stations
WAN interfaces
XDSL interfaces
CSU/DSU equipment
Secondary lightning protection per IEC61000-4-5 up
to Class 4 with 12 & 42 Ohms source impedance,
and up to Class 3 protection with 2 Ohms source
impedance
MECHANICAL AND PACKAGING
• Molded SO-16W Surface Mount
• Weight 0.25 grams (approximate)
• Marking: Logo, device marking code, date code
• Pin #1 defined by dot on top of package
• Tape & Reel per EIA Standard 481
• 13 inch reel; 2,500 pieces (OPTIONAL)
• Carrier tubes; 45 pcs (STANDARD)
Operating temperature: -55°C to +150°C
Storage temperature: -55°C to +150°C
Peak pulse power: 1500 watts (10/1000 µs, Fig 1)
Pulse repetition rate: < .01%
Thermal resistance:< 30°C/watt (junction-to-case)
Lead soldering temperature: 260°C, 10s maximum
ELECTRICAL CHARACTERISTICS PER LINE PAIR @ 25°C Unless otherwise specified
MIN
MAX
MAX
MAX
TYP
8.0
15
16
25
50
MAX
LC01-6
DEVICE
MARKING
LC01-6
6.0
µA
Note: Transient Voltage Suppressor (TVS) product is normally selected based on its stand off voltage VWM. Product selected voltage should be
equal to or greater than the continuous peak operating voltage of the circuit to be protected.
Copyright 2004
10-25-2004 REV B
Microsemi
Scottsdale Division
8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503
Page 1
LC01-6
STANDBY
CURRENT
ID
@ VWM
VOLTS
CLAMPING
VOLTAGE
VC
@ 200 Amp
(Figure 3)
VOLTS
BREAKDOWN
VOLTAGE
VBR
@1 mA
VOLTS
PART
NUMBER
MAXIMUM
CAPACITANCE
C
@0V,
f =1 MHz
CLAMPING
VOLTAGE
VC
@ 100 Amp
(Figure 2)
VOLTS
STAND OFF
VOLTAGE
VWM
