REVISION EX
DO NOT
SCALE FROM
THIS PRINT
FTSH-1XX-XX-XXX-DV-XXX-XXX
NOTES:
1. C REPRESENTS A CRITICAL DIMENSION.
2. PARTS MAY BE CUT TO POSITION.
No OF POSITIONS
3. MAXIMUM CUT FLASH: .015[0.38],
-02 THRU -50
LOOSE FLASH MUST BE REMOVED.
(PER ROW)
4. MINIMUM PUSHOUT FORCE: 1.0 LB.
LEAD STYLE
5. MEASURED AT BEND RADIUS, NOT AT END OF PIN.
6. TUBE ONLY -04 THROUGH -50 POSITIONS (SEE TABLE 2).
-01: .120 [3.05]
7. SHEAR TAILS TO DIMENSION SHOWN.
-02: .075 [1.91]
8. MAXIMUM BURR ALLOWANCE: .003 [0.08]
-03: .065 [1.65]
9. GOLD PLATING TO BE ON POST, TIN PLATING TO BE ON TAIL.
-04: .150 [3.81]
10. FILL WITH ALIGNMENT PIN HOLES TO TAIL SIDE.
-05 .170 [4.32]
11. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, LOCKING CLIPS
-14: .150 [3.81](NOT AVAILABLE
ARE NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS
WITH -SM, FM, LM PLATING
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH LOCKING CLIPS.
OPTIONS)
12. VOIDS MAY OR MAY NOT BE PRESENT ON POSITIONS 5 THRU 8 AND CAN
BE MIXED WITHIN AN ORDER.
PLATING SPECIFICATION
13. ON LEAD STYLES -02 THROUGH -03 THE T-1S15-03 CAN
BE SUBSTITUTED FOR T-1S15-14.
-L: 10µ" SELECTIVE GOLD IN CONTACT AREA,
14. ON LEAD STYLES -01 AND -04, T-1S15-17 CAN BE
MATTE TIN ON TAIL
SUBSTITUTED FOR T-1S15-15-XXX.
-F: 3µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
-S: 30µ" SELECTIVE GOLD IN CONTACT AREA,
C
MATTE TIN ON TAIL
-H: 30µ" GOLD IN CONTACT AREA,
No OF POS x .0500 +.005 [ +0.13 ]
-.010 -0.25
3µ" GOLD ON TAIL
(No OF POS x .0500[1.27]) - .050[1.27]
-LM: 10µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
02
-FM: 3µ" SELECTIVE GOLD IN CONTACT AREA,
50
MATTE TIN ON TAIL
-SM: 30µ" SELECTIVE GOLD IN CONTACT AREA,
MATTE TIN ON TAIL
.135 3.43 -LTL: 10µ" SELECTIVE GOLD IN CONTACT AREA,
TIN/LEAD (90/10+/-5%) TAIL
REF
-G: 10µ" GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
49
01
FTSHC-50-D
2 MAX SWAY
(EITHER DIRECTION)
XXX INDICATES POSITION TO BE OMITTED
(NOT AVAILABLE WITH EXX OPTIONS)
(ONLY AVAILABLE WITH -F, -FM, -L, -LM PLATING OPTIONS)
2 MAX SWAY
(EITHER DIRECTION)
C
.099 2.51
REF
+.005
FIG 1
+0.13
.115 - .003 2.92 - 0.08
(SEE NOTE 5)
.004[.10]
FTSH-1XX-XX-XXX-DV SHOWN
(SEE FTSHC-1XX-XX-XXX-DX-XX PRINT FOR DETAILS)
.23 5.8
(SEE NOTE 7)
SEE NOTE 8
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [.3]
1
.XXX: .005 [.13]
.XXXX: .0010 [.025]
MATERIAL:
.230 5.84 REF
HAND FILL USING T-1S40
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
SHEET SCALE: 5:1
INSULATOR: LCP UL 94 VO
TERMINAL: PHOSPHOR BRONZE
* = SEE NOTE 13
*** = SEE NOTE 14
* = NOT ENGINEERING APPROVED
90°±3°
"A" C
SEE NOTE 3
(2 PLCS)
5713755 / 5961339
POLARIZING OPTION
C
.050±.008 1.27±0.20
SEE TABLE 1
"B"
CONTACT AREA
(SEE NOTE 9 & TABLE 1)
PATENT NUMBERS
TAIL OPTION
-DV: DOUBLE VERTICAL
(USE **FTSHC-1XX-XX-XXX-DV FOR ALL OPTIONS
EXCEPT -ES, -EJ, -EJM, -EJC, -EC, -EP, -EL, -EPC, -A,
THEN USE FTSH-50-D AND BUILD PER PRINT)
** = SEE FTSHC-1XX-XX-XXX-DX-XX PRINT FOR DETAILS
2 MAX SWAY
(EITHER DIRECTION)
.016 0.41 SQ
REF (TYP)
OPTIONS
-P: PICK & PLACE PAD (4 POS MIN)
(SEE FIG 11, SHT 4 & TABLE 5)
-TR: TAPE & REEL PACKAGING
-ES: END SHROUDS (SEE FIG 6, SHT 3)
(MOLDED IN 5 POS MIN; -02 & -03 LEAD STYLE ONLY)
(SNAP SHROUDS 9 POS MIN; -02 & -03 LEAD STYLE ONLY)
(MUST USE FTSH-50-D)
-EJ: EJECTOR SHROUDS: SEE FIG 4, SHT 2)
(10 POS MIN; -01 LEAD STYLE ONLY)(MUST USE FTSH-50-D)
-EJM: EJECTOR SHROUDS WITH MOLDED ALIGNMENT PIN
(SEE FIG 5, SHT 2; 10 POS MIN; -01 LEAD STYLE ONLY)
(NOT VALID WITH -A OPTION)(MUST USE FTSH-50-D)
-EJC: EJECTOR SHROUDS WITH LOCKING CLIP
(SEE FIG 5, SHT 2 & NOTE 11)
(10 POS MIN; -01 LEAD STYLE ONLY; NOT VALID WITH -A
OPTION)
(MUST USE FTSH-50-D)
-EC: LOCKING CLIP (SEE FIG 7, SHT 3 & NOTE 11)
(9 POS MIN; -02 & -03 LEAD STYLE ONLY)(MUST USE FTSH-50-D)
-EP: GUIDE POST (SEE FIG 8, SHT 3; 9 POS MIN; -02 & -03 LEAD STYLE
ONLY)
(USE ONLY WHEN MATING WITH CLP)(MUST USE FTSH-50-D)
-EL: BOARD LOCK (SEE FIG 9, SHT 3)
(9 POS MIN; -02 & -03 LEAD STYLE ONLY)
(USE ONLY WHEN MATING WITH CLP)(MUST USE FTSH-50-D)
-EPC: GUIDE POST & LOCKING CLIP
(SEE FIG 10, SHT 3 & NOTE 11; USE ONLY WHEN MATING WITH CLP)
(9 POS MIN; -02 & -03 LEAD STYLE ONLY; NOT VALID
WITH -A OPTION)(MUST USE FTSH-50-D)
-A: ALIGNMENT PIN (MOLDED OR STAKED; SEE FIG 3, SHT 2)
(MOLDED: 3 POS MIN; STAKED: 6 POS MIN)
(SAMTEC DISCRETION ON WHICH -A PIN USED)
(MUST USE FTSH-50-D)
-K: KEYING OPTION FOR MATING WITH FFSD
(SEE TABLE 3, SHT 2; 05 THRU 25 AVAILABLE AS STANDARD)
(POSITION 13, 17, 20 & 25 AVAILABLE WITH -EJ OPTION)
(LEAD STYLE -01 ONLY, SEE FIG 2, SHT 2 & NOTE 12)
(ALIGNMENT PIN AVAILABLE WITH -K OPTION BUT MUST BE MOLDED)
(MUST USE FTSH-XX-CN-XX)
METAL PICK & PLACE PAD (5 POS
MPP-22-5)
*-M: (SEE FIG 12, SHT 4; NOT AVAILABLEMIN; USEOPTION)
WITH -K
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
.050 x .050 CL DOUBLE VERTICAL SMT TERMINAL STRIP
DWG. NO.
FTSH-1XX-XX-XXX-DV-XXX-XXX
F:\DWG\MISC\MKTG\FTSH-1XX-XX-XXX-DV-XXX-XXX-MKT.SLDDRW
BY: PURVIS
10/12/1995
SHEET 1 OF 5
