Super Capacitor HV Series
Dimensions
H
Markings
ͬL min.
L min.
2.7V
10F
SuperCapacitor
P±0.1
φ D±0.5
Negative polarity
HV
φd
Anode polarity
Standard Rating
Part No.
HV0E106NF
HV0E226NF
HV0E506NF
HV0E107NF
Max. Operating
Voltage
(Vdc)
2.7
2.7
2.7
2.7
Nominal
Capacitance
(F)
10
22
50
100
Max. ESR
(at 1 kHz)
(m⏲)
100
100
30
30
Max. Current
at 30 minutes
(mA)
8
18
40
81
Dimensions (Unit: mm)
D
10.0
12.5
18.0
22.0
35±2
35±2
40±5
50±5
P
d
L
ͬL
Weight
(g)
5.0
5.0
7.5
10.2
0.6
0.6
0.8
1.0
15.0
15.0
15.0
15.0
5.0
5.0
5.0
5.0
4.5
6.5
14.0
24.0
H
Specifications
Item
Operating Temperature Range
Maximum Operating Voltage
Nominal Capacitance Range
Capacitance Allowance
Equivalent Series Resistance (ESR)
Current at 30 minutes
Phase 2
Tempere Variation of
Characteristics
Phase 4
Phase 5
Lead Strength (Tensile)
Vibration Resistance
Solderability
Soldering Heat Resistance
Temperature Cycle
Humidity Resistance
High Temperature Load Life
Specifications
–25˚C to +60˚C (50F, 100F), –25˚C to +70˚C (10F, 22F)
2.7 Vdc
10F, 22F, 50F, 100F
±30%
Refer to standard ratings
Refer to standard ratings
Capacitance
More than 50% of initial value
ESR
Not to exceed 4 times initial value
Capacitance
Not to exceed 150% of initial value
ESR
Not to exceed initial requirement
Current at 30minutes Not to exceed 1.5CV(mA)
ͬC/C
Within ±20% of initial value
ESR
Not to exceed initial requirement
Current at 30 minutes Not to exceed initial requirement
No loosening nor permanent damage of the leads
Caoacitance
ESR
Meet initial standard value
Current at 30 minutes
Appearance
Noobvious abnormality
3/4 or more of the pin surface should be covered
with new solder
Capacitance
ESR
Current at 30 minutes
Appearance
Capacitance
ESR
Current at 30 minutes
Appearance
Capacitance
ESR
Current at 30 minutes
Appearance
Capacitance
ESR
Current at 30 minutes
Appearance
Should satisfy initial standard value
No obvious abnormality
Meet initial standard value
No obvious abnormality
Within ±20% of initial value
1.2 or less time initial standard value
1.2 or less time initial standard value
No obvious abnormality
Within ±30% of initial value
Twice or less times initial standard value
Twice or less times initial standard value
No obvious abnormality
Test Conditions Conforming to JIS C 5102–1994
Conforms to 7.12
Phase2: –25±2˚C
Phase4: +60±2˚C
Phase5: +25±2˚C
Conforms to 8.1.2 (1)
Conforms to 8.2.3 (1)
Frequency: 10 to 55Hz
Test duration: 6 hours
Conforms to 8.4
Solder temperature: 245±5˚C
Dipping duration: 5±0.5sec.
Shold be dipped up to 1.6mm from the lower
end of the capacitor
Conforms to 8.5
Solder temperature: 260±10˚C
Dipping duration: 10±1sec.
Shold be dipped up to 1.6mm from the lower
end of the capacitor
Conforms to 9.3
+70˚C(10F, 20F)
Temperature: –25˚CǞR.T.Ǟ+60˚C(50F, 100F)ǞR.T.
Number of cycles: 5 cycles
Conforms 9.5
Temperature: 40±2˚C
Relative humidity: 90 to 95% RH
Test duration: 240±8hours
Conforms 9.10
Temperature: +70˚C(10F, 20F) ±2˚C
+60˚C(50F, 100F)
Voltage applied: 2.7Vdc
Test duration: 1000+48 hours
–0
Series protection resistance: 0⏲
Super Capacitors Vol.07 11
●All specifications in this catalog and production status of products are subject to change without notice. Prior to the purchase, please contact NEC TOKIN for updated product data.
●Please request for a specification sheet for detailed product data prior to the purchase.
●Before using the product in this catalog, please read "Precautions" and other safety precautions listed in the printed version catalog.
2007.08.03 P0862SUCA16VOL07E