FEATURES
FUNCTIONAL BLOCK DIAGRAM
Isolated RS-485/RS-422 transceiver, configurable as half or
full duplex
isoPower® integrated isolated dc-to-dc converter
±15 kV ESD protection on RS-485 input/output pins
Complies with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E)
ADM2582E data rate: 16 Mbps
ADM2587E data rate: 500 kbps
5 V or 3.3 V operation
Connect up to 256 nodes on one bus
Open- and short-circuit, fail-safe receiver inputs
High common-mode transient immunity: >25 kV/µs
Thermal shutdown protection
Safety and regulatory approvals
UL recognition: 2500 V rms for 1 minute per UL 1577
VDE Certificates of Conformity
DIN EN 60747-5-2 (VDE 0884 Part 2): 2003-01
VIORM = 560 V peak
Operating temperature range: −40°C to +85°C
Highly integrated, 20-lead, wide-body SOIC package
VISOOUT
VCC
isoPower DC-TO-DC CONVERTER
OSCILLATOR
RECTIFIER
VISOIN
REGULATOR
DIGITAL ISOLATION iCoupler
TRANSCEIVER
Y
TxD
ENCODE
DECODE
D
Z
DE
ENCODE
DECODE
RxD
DECODE
ENCODE
A
R
B
ADM2582E/ADM2587E
RE
GND1
ISOLATION
BARRIER
GND2
08111-001
Data Sheet
Signal and Power Isolated RS-485
Transceiver with ±15 kV ESD Protection
ADM2582E/ADM2587E
Figure 1.
APPLICATIONS
Isolated RS-485/RS-422 interfaces
Industrial field networks
Multipoint data transmission systems
GENERAL DESCRIPTION
The ADM2582E/ADM2587E are fully integrated signal and
power isolated data transceivers with ±15 kV ESD protection
and are suitable for high speed communication on multipoint
transmission lines. The ADM2582E/ADM2587E include an
integrated isolated dc-to-dc power supply, which eliminates the
need for an external dc-to-dc isolation block.
They are designed for balanced transmission lines and comply
with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E).
The devices integrate Analog Devices, Inc., iCoupler® technology
to combine a 3-channel isolator, a three-state differential line driver,
a differential input receiver, and Analog Devices isoPower dc-to-dc
converter into a single package. The devices are powered by a
single 5 V or 3.3 V supply, realizing a fully integrated signal and
power isolated RS-485 solution.
Rev. F
The ADM2582E/ADM2587E driver has an active high enable.
An active low receiver enable is also provided, which causes the
receiver output to enter a high impedance state when disabled.
The devices have current limiting and thermal shutdown
features to protect against output short circuits and situations
where bus contention may cause excessive power dissipation.
The parts are fully specified over the industrial temperature
range and are available in a highly integrated, 20-lead, wide-body
SOIC package.
The ADM2582E/ADM2587E contain isoPower technology that
uses high frequency switching elements to transfer power through
the transformer. Special care must be taken during printed circuit
board (PCB) layout to meet emissions standards. Refer to the
AN-0971 Application Note, Control of Radiated Emissions with
isoPower Devices, for details on board layout considerations.
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2009–2016 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
