MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Dual 3-Input 3-Output OR
Gate
MC10H210
The MC10H210 is designed to drive up to six transmission lines simultan–
eously. The multiple outputs of this device also allow the wire “OR”–ing of
several levels of gating for minimization of gate and package count.
The ability to control three parallel lines with minimum propagation delay
from a single point makes the MC10H210 particularly useful in clock distribution
applications where minimum clock skew is desired.
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
• Propagation Delay Average, 1.0 ns Typical
• Power Dissipation, 160 mW Typical
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
VEE
VI
–8.0 to 0
Vdc
0 to VEE
Vdc
LOGIC DIAGRAM
5
6
7
2
9
10
11
12
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
Iout
50
100
mA
Operating Temperature Range
TA
Tstg
0 to +75
°C
–55 to +150
–55 to +165
°C
°C
Storage Temperature Range — Plastic
— Ceramic
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
0°
Characteristic
Symbol
Min
Power Supply Current
IE
IinH
IinL
Input Current High
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
25°
Max
Min
—
42
—
720
0.5
—
3
4
13
14
75°
Max
Min
Max
—
38
—
450
—
42
mA
—
450
0.5
—
µA
0.3
—
µA
–0.735
VCC1 = PINS 1, 15
VCC2 = PIN 16
VEE = PIN 8
Unit
Vdc
VOH
VOL
–1.02 –0.84 –0.98 –0.81 –0.92
–1.95 –1.63 –1.95 –1.63 –1.95
–1.60
Vdc
VIH
VIL
–1.17 –0.84 –1.13 –0.81 –1.07
–0.735
Vdc
–1.95 –1.48 –1.95 –1.48 –1.95
–1.45
DIP
PIN ASSIGNMENT
Vdc
VCC1
16
VCC2
AOUT
AC PARAMETERS
1
2
15
VCC1
0.5
1.55
0.55
1.55
0.6
1.7
ns
AOUT
3
14
BOUT
Rise Time
tpd
tr
0.75
1.8
0.75
1.9
0.8
2.0
ns
AOUT
4
13
BOUT
Fall Time
tf
0.75
1.8
0.75
1.9
0.8
2.0
ns
AIN
5
12
BOUT
AIN
6
11
BIN
AIN
7
10
BIN
VEE
8
9
BIN
Propagation Delay
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated
through a 50–ohm resistor to –2.0 volts.
Note: If crosstalk is present, double bypass capacitor to 0.2 µF.
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
© Motorola, Inc. 1996
2–293
REV 5
