SY10EL57
SY100EL57
SY10EL57
4:1 DIFFERENTIAL
MULTIPLEXER
Micrel, Inc.
FEATURES
SY100EL57
DESCRIPTION
s 5V power supply
s Useful as either 4:1 or 2:1 multiplexer
s VBB output for single-ended operation
s 75KΩ internal input pulldown resistors
s Available in 150 mil 16-pin SOIC package
The SY10/100EL57 are fully differential 4:1 multiplexers.
By leaving the SEL1 line open (pulled LOW via the input
pulldown resistors) the device can also be used as a
differential 2:1 multiplexer with SEL0 input selecting between
D0 and D1. The fully differential architecture of the EL57
makes it ideal for use in low skew applications such as
clock distribution.
The SEL1 is the most significant select line. The binary
number applied to the select inputs will select the same
numbered data input (i.e., 00 selects D0).
Multiple VBB outputs are provided for single-ended or
AC coupled interfaces. In these scenarios, the VBB output
should be connected to the data bar inputs and bypassed
via a 0.01µF capacitor to ground. Note that the VBB output
can source/sink up to 0.5mA of current without upsetting
the voltage level.
PIN NAMES
TRUTH TABLE
SEL1
SEL0
DATA OUT
Pin
L
L
D0
D0-3
Differential Data Inputs
L
H
D1
SEL0, 1
Mux Select Inputs
H
L
D2
VBB1, 2
Reference Outputs
H
H
D3
Q
Data Outputs
M9999-021910
hbwhelp@micrel.com or (408) 955-1690
1
Function
Rev.: H
Amendment: /0
Issue Date: February 2010
SY10EL57
SY100EL57
Micrel, Inc.
ABSOLUTE MAXIMUM RATINGS(1)
Symbol
Rating
Value
Unit
VEE
Power Supply (VCC = 0V)
–8.0 to 0
V
VIN
Input Voltage (VCC = 0V)
0 to -6.0
V
IOUT
Output Current
- Continuous
- Surge
50
100
mA
TLEAD
Lead Storage Temperature
+260
˚C
TA
Operating Temperature Range
-40 to +85
˚C
VEE
Operating Range(1), (2)
-5.7 to -4.2
V
Notes:
1. Absolute maximum ratings, beyond which, device life may be impaired, unless otherwise specified on an individual data sheet.
2. Parametric values specified at:
5 volt Power Supply Range 100EL57 Series:
-4.2V to -5.5V.
10EL57 Series
-4.75V to -5.5V.
10EL DC CHARACTERISTICS
VEE = -5.5 to -4.75V; VCC = GND = 0V(1)
TA = -40˚C
Symbol
Parameter
TA = 0˚C
TA = +25˚C
TA = +85˚C
Min.
Max.
Min.
Max.
MIn.
Max.
Min.
Max.
Unit
VOH
Output HIGH Voltage
-1080
-890
-1020
-840
-980
-810
-910
-720
mV
VOL
Output LOW Voltage
-1950
-1650
-1950
-1630
-1950
-1630
-1950
-1595
mV
VIH
Input HIGH Voltage
-1230
-890
-1170
-840
-1130
-810
-1060
-720
mV
VIL
Input LOW Voltage
-1950
-1500
-1950
-1480
-1950
-1480
-1950
-1445
mV
IIL
Input LOW Current
0.5
—
0.5
—
0.5
—
0.5
—
µA
Note:
1. 10EL circuits are designed to meet the DC specifications shown in the table after thermal equilibrium has been established. The circuit is in a test
socket or mounted on a printed circuit board and transverse airflow greater than 500lfpm is maintained. Outputs are terminated through a 50Ω
resistor to -2.0V except where otherwise specified on the individual data sheets.
100EL DC CHARACTERISTICS
VEE = -5.5 to -4.75V; VCC = GND = 0V(1)
TA =-40˚C
Symbol
Parameter
TA =0˚C to 85C
Min.
Typ.
Max.
Min.
Typ.
Max.
Unit
Condition
VOH
Output HIGH Voltage
-1085
-1005
-880
-1025
-955
-880
mV
VIN = VIH (Max) or VIL (Min)
VOL
Output LOW Voltage
-1830
-1695
-1555
-1810
-1705
-1620
mV
VIN = VIH (Max) or VIL (Min)
VOHA
Output HIGH Voltage
-1095
—
—
-1035
—
—
mV
VIN = VIH (Min) or VIL (Max)
VOLA
Output LOW Voltage
—
—
-1555
—
—
-1610
mV
VIN = VIH (Min) or VIL (Max)
VIH
Input HIGH Voltage
-1165
—
-880
-1165
—
-880
mV
VIL
Input LOW Voltage
-1810
—
-1475
-1810
—
-1475
mV
IIL
Input LOW Current
0.5
—
—
0.5
—
—
µA
VIN = VIL (Max)
Note:
1. The same DC parameter values at VEE = -4.5V now apply across the full VEE range of -4.2V to -5.5V. Outputs are terminated through a 50Ω resistor
to -2.0V except where otherwise specified on the individual data sheets.
M9999-021910
hbwhelp@micrel.com or (408) 955-1690
3