MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Quad 2-Input Multiplexer
(Non-Inverting)
MC10H158
The MC10H158 is a quad two channel multiplexer with common input select.
A “high” level select enables input D00, D10, D20 and D30 and a “low” level
select enables input D01, D11, D21 and D31. This MECL 10H part is a
functional/pinout duplication of the standard MECL 10K family part, with 100%
improvement in propagation delay and no increase in power–supply current.
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
• Propagation Delay, 1.5 ns Typical
• Power Dissipation, 197 mW Typical
• Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
• Voltage Compensated
• MECL 10K–Compatible
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
VEE
VI
–8.0 to 0
Vdc
0 to VEE
Vdc
50
100
mA
0 to +75
–55 to +150
–55 to +165
Power Supply (VCC = 0)
Input Voltage (VCC = 0)
Output Current — Continuous
— Surge
Iout
Operating Temperature Range
TA
Tstg
Storage Temperature Range — Plastic
— Ceramic
TRUTH TABLE
Select
D0
D1
Q
°C
L
X
L
L
°C
°C
L
X
H
H
H
L
X
L
H
H
X
H
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%)
0°
25°
75°
Characteristic
Symbol
Min
Max
Min
Max
Min
Max
Unit
Power Supply Current
IE
IinH
—
53
—
48
—
53
mA
Input Current High
Pin 9
Pins 3–6 and 10–13
DIP
PIN ASSIGNMENT
µA
—
—
475
515
—
—
295
320
—
—
295
320
0.5
—
0.5
—
0.3
—
µA
Q0
1
16
VCC
–1.02 –0.84 –0.98 –0.81 –0.92
–0.735
Vdc
Q1
2
15
Q2
–1.95 –1.63 –1.95 –1.63 –1.95
–1.60
Vdc
D11
3
14
Q3
High Input Voltage
VOL
VIH
–1.17 –0.84 –1.13 –0.81 –1.07
–0.735
Vdc
D10
VIL
–1.95 –1.48 –1.95 –1.48 –1.95
–1.45
Vdc
4
13
D20
Low Input Voltage
D01
5
12
D21
D00
6
11
D30
NC
7
10
D31
VEE
8
9
SELECT
Input Current Low
High Output Voltage
Low Output Voltage
IinL
VOH
AC PARAMETERS
Propagation Delay
Data
Select
Rise Time
Fall Time
tpd
ns
0.5
1.0
tr
tf
1.9
2.9
0.5
1.0
1.9
2.9
0.5
1.0
2.0
2.9
0.7
2.2
0.7
2.2
0.7
2.2
ns
0.7
2.2
0.7
2.2
0.7
2.2
ns
NOTE:
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through
a 50–ohm resistor to –2.0 volts.
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
3/93
© Motorola, Inc. 1996
2–238
REV 5
