(1/4)
001-01 / 20030823 / e9635_zjsc.fm
ZJSC Series
3-Terminal Filters for Signal Line and DC Power Line
Lead
EMC Components
FEATURES
• With a lead pitch of 2.5mm (identical to the terminal pitch of DIP
type ICs), the ZJSC series T-type EMC filters enable the design
of high-density circuit board configurations using automated
insertion.
• Their sharp cutoff characteristics provide effective highfrequency attenuation with minimum effect on passband signals,
even when such signals are at close proximity to the trapband.
• The series are available in an extensive range of cutoff
frequencies, enabling their use in a wide range of applications.
• The use of highly miniaturized inductor elements helps minimize
variations in the mounted heights of circuit board components.
APPLICATIONS
Home electronic equipment, (TVs, VCRs, CD players, DAT players, electric musical instruments, PCs, etc.), office automation
equipment (computers, terminals, stand-alone word processors,
fax machines, etc.), factory automation equipmen
BASIC CHARACTERISTICS
Rated voltage Edc
Withstand voltage Edc
[Between terminal No.1, 3 to 2]
Insulation resistance
[DC. 50V for 1min]
Operating temperature range
50V max.
125V
10000MΩ min.
–25 to +85°C
This plus the use of round leads ensures superior clinchability
and insertability, making this product ideal for use in automated
mounting production lines.
PRODUCT IDENTIFICATION
ZJSC - 2R2 - 101 - TA
(1)
(2) (3) (4)
(1)Series name
(2)Inductance value 2R2:2.2µH×2
(3)Capacitance 101:100pF
(4)Packaging style TA: Taping∗
∗ Only used for bulk packaged products. This should become
“TAH” when using TDK’s AVI-SERT automatic assembly equipment feeder.
SHAPES AND DIMENSIONS
TAPING SPECIFICATIONS
Dimensions in mm
A1
Marking
T
P
Dh
A
Dh
F1
F2
øD0
W
t
P0
l1
W0
(P 1)
W1
H
H1
ød 2
ød 1
(W 2 )
ød 2
BULK SPECIFICATIONS TYPICAL MOUNTING EXAMPLE
2.54mm pitch
Marking
1
2
l
ZJSC series
f1 f 2
IC LSI
3
• All specifications are subject to change without notice.
Component width
Component height
Component thickness
A1
7.5max.
A
8max.
T
2.4max.
ød1
0.5±0.05
Lead wire diameter (round)
0.6±0.05
ød2
Component pitch
P
12.7±1
Feed hole pitch∗1
P0
12.7±0.3
6.35±0.4
Feed hole position error
P1
F 1 , F2
2.5+0.4, –0.1
Lead pitch∗2
Component alignment
∆h
0±2
Tape width
W
18+1, –0.5
Cover tape width
W0
12±0.3
9±0.5
Feed hole position error
W1
(4max.)
Cover tape position
(W2)
Component bottom position∗3 H
16±1
24.5max.
Maximum component height∗4 H1
4±0.2
Feed hole diameter
øD0
Total tape thickness
t
0.5±0.2
Lead wire protrusion
l1
0.5max.
Lead wire length
l
5±1.5
f1, f2
2.5±0.5
Lead pitch∗5
∗1 The permissible cumulative pitch error is within ±1mm of 20 pitches.
∗2 The dimension at the end of the lead pitch is also within the tolerance.
∗3, ∗4 When TAH has been set in the taping specification ∗3 and ∗4, it
becomes 20±1mm and 28mm max. respectively.
∗5 The tolerance of lead pitch is the dimensions when a lead is released
from the tape. Not available for bulk packaging.