8060 Series
Alternate Action and Momentary Pushbutton Switches
Features/Benefits
• Long travel
• Available with LED
• Long life contact design
• Epoxy terminial seal
Pushbutton
A
Typical Applications
• Instrumentation
• Computers and peripherals
• Telecommunications and
networking equipment
compatabile with bottom
wash cleaning
• RoHS compliant models
available
Models Available
Specifications
Materials
CONTACT RATING: Q contact material: 6 AMPS @ 120 V AC
or 28 V DC; 3 AMPS @ 250 V AC. See page A-59 for
additional ratings.
CASE: Glass filled nylon 6/6 or diallyl phthalate (DAP),
flame retardant (UL 94V-0).
PLUNGER: S, S1, S2 Options: Glass filled nylon or glass filled
polyester (PBT) (UL 94V-0). L, L1 Options: Brass, nickel plated.
ELECTRICAL LIFE: 50,000 make-and-break cycles at full load.
CONTACT RESISTANCE: Below 20 mΩ typ. initial @
2-4 V DC, 100 mA, for both silver and gold plated contacts.
INSULATION RESISTANCE: 109Ω min.
CAP & FRAME: Nylon, black standard.
DIELECTRIC STRENGTH: 1,000 Vrms min. @ sea level.
SWITCH SUPPORT: Brass or steel, matte-tin plated.
OPERATING TEMPERATURE: –30ºC to 65ºC
END CONTACTS: Q contact material: Coin silver, silver plated.
See page A-59 for additional contact materials.
BUSHING: Brass or zinc, nickel plated.
HOUSING: Stainless steel.
SOLDERABILITY: Per MIL-STD-202F method 208D, or
EIA RS-186E method 9 (1 hour steam aging).
CENTER CONTACT & ALL TERMINALS: Q contact material: Copper
alloy, silver plated. See page A-59 for additional contact materials.
CAP INSTALLATION FORCE: 10 lbs. maximum permissible.
NOTE: Any models supplied with P, R, S, Q, B or G contact material are RoHS compliant.
TERMINAL SEAL: Epoxy. Refer to soldering and cleaning
in Technical Data Chapter.
NOTE: Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
HARDWARE: Nut & Locking Ring: Brass, nickel plated;
Lockwasher: Steel, nickel plated.
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown
and described on pages A-53 thru A-61. For additional options not shown in catalog, consult Customer Service Center. All
models have epoxy terminal seal and are compatible with all “bottom-wash” PCB cleaning methods.
Switch Function
8161
SPDT On-On
8168
SPDT On-Mom.
8261
DPDT On-On
Actuator or Plunger
S
.710" high plunger
with .375" dia. cap
J80 Snap-in
J81 Snap-in with frame
J82 Snap-in with frame for LED
J86 Snap-in with frame & LED
L
.740" high plunger with
.395" dia. cap
L1 .740" high plunger with
.590" dia. cap
S1 .615" high plunger with
.200" dia. cap
S2 .710" high plunger with
.310" dia. cap
Bushing
H .300" high, flat, hi torque
H9 .300" high, flat, hi torque
NONE No bushing choice required
Y3 7.6mm, keyway
Terminations
Right angle, PC thru-hole
A
AV2 Vertical right angle,
PC thru-hole
C
PC Thru-hole
Z
Solder lug
A3 Right angle, snap-in, PC thru-hole
AV3 Vertical right angle, snap-in,
PC thru-hole
V3 .460" high, V-bracket
V4 .630" high, V-bracket
V6 .460" high, V-bracket
V21 .555" high, snap-in V-bracket
V31 .460" high, snap-in V-bracket
W .750" long, wire wrap
Z3 Quick connect
Contact Material
B Gold
P Gold, matte-tin
Q Silver
S Silver, matte-tin
G Gold over silver
R Gold over silver,
matte-tin
Seal
E Epoxy
I Epoxy potted base
Cap Color
2 Black
1 White
3 Red
4 Orange
5 Yellow
9 Gray
Frame Color
2 Black
LED Color
3 Red
NONE Models without LED
Dimensions are shown: Inches (mm)
Specifications and dimensions subject to change
A-52
www.ck-components.com
