PXC-Series
ALUMINUM ELECTROLYTIC CAPACITORS
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
Surface Mount
Upgrade!
@Super low ESR, impedance and high heat resistance have been obtained by using
conductive polymer as electrolyte
@Rated voltage range : 2.5 to 25Vdc, case size range : F6.3B5.5mm to F10B12.2mm
(Case code H12 and J12 newly added)
@Suitable for DC-DC converters, voltage regulators and decoupling applications used to
computer motherboards etc.
@High heat resistance to reflow soldering (See reflow soldering conditions)
?SPECIFICATIONS
Items
Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
-55 to +105C
2.5 to 25Vdc
P20% (M)
Rated voltageB1.15V
Shall not exceed values shown in STANDARD RATINGS.
(at 20C, 120Hz)
(at 105C)
(at 20C after 2 minutes)
0.12 max.
(at 20C, 120Hz)
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours
at 105C.
Appearance
No significant damage
Capacitance change
[P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 500 hours.
Appearance
No significant damage
Capacitance change
[P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
[P20% of the initial value
DF (tanE)
[150% of the initial specified value
ESR
[150% of the initial specified value
Leakage current
[The initial specified value
1% per 1000 hours maximum (Confidence level 60% at 105C)
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
?DIMENSIONS (Terminal Type=VC) [mm]
?MARKING
EX) PXA16VC39M
P
CP0.2
BP0.2
FDP0.5
W
0.3max.
AP0.2
LP0.3 (Note)
Note : LP0.5 for H12 and J12
Case code
F55
F60
H70
J80
H12
J12
fD
6.3
6.3
8
10
8
10
L
A
B
C
5.2 6.6 6.6 7.2
5.7 6.6 6.6 7.2
6.7 8.3 8.3 9.0
7.7 10.3 10.3 11.0
12.0 8.3 8.3 9.0
12.2 10.3 10.3 11.0
W
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
0.7 to 1.1
P
1.9
1.9
3.1
4.5
3.1
4.5
A905
39
16V
?PART NUMBERING SYSTEM
PXA
16
VC
39
M
F60
Case code
Cap tolerance (P20%)
Nominal cap code
Terminal type (VC)
Rated voltage in volts
Series name
Capacitance
39MF
100MF
1000MF
Code
39
100
1000
(1/2)
CAT. No. E1001D
