HOME在庫検索>在庫情報

部品型式

GL3HD43

製品説明
仕様・特性

General Description of Light Emitting Diodes I Handling Precautions This product is sensitive to static electricity and demands a lot of attention. Please take all possible measures for static electricity and surge solution. I Lead Forming Method ;; ;;; Hold a lead pin firmly when forming I Installation (1) Installation on a PWB When mounting an LED lamp on a PWB, do not apply physical stress to the lead pins. (Notes)¡The lead pin pitch should match the PWB pin-hole pitch: do not broaden out or narrow down the lead pins. ¡When positioning an LED lamp, basically employ an LED with tie-bar cut or use a spacer. (4) Installation to the case Do not fix part A with adhesives when fixed to the case as shown in the figure. A hole of the case should be designed not to be smaller than the outside diameter of LED lamp resin. I Soldering Conditions ; ;; ;; ;; ;; ;; ; PWB Acceptable ; ;; ;; ;; ; Case Type of Soldering 1. Manual soldering 2. Wave soldering Conditions 295˚C ± 5˚C, within 3 seconds 260˚C ± 5˚C, within 5 seconds Preheating 70˚C to 80˚C, within 30 seconds Soldering 245˚C ± 5˚C, within 5 seconds (Notes)¡Avoid dipping resin into soldering bath. ¡Avoid applying stress to lead pins while they are heated. For example, when the LED lamp is moved with the heat applied to the lead pins during manual soldering or solder repair, disconnection may occur. I Cleaning Conditions described below shall be observed in cleaning. (1) Solvent cleaning : Solvent temperature 45˚C or less, for 3 min. (2) Ultrasonic cleaning : The affect on the device is different depending on the size of the cleaning bath, ultrasonic output, board size, and device mounting method. Test the cleaning method under actual conditions and check the abnormalities before actual use. (3) Recommended solvents are shown below. Melthyl alcohol, Ethyl alcohol, Isopropyl alcohol. When other solvents are used, package resin may be penetrated by solvents. Please confirm under actual conditions before use. ;;; ;;; ;; ;; ;; (2) When an LED lamp is mounted directly on a PWB If the bottom face of an LED lamp is mounted directly on singlesided PWB (1.6mm t or more), the base of the lead pins may be subjected to have physical stress due to PWB warp, cutting or clinching of lead pins. Prior to use, be sure to check that no disconnection inside of the resin or damage to resin etc., is found. When an LED lamp is mounted on a double-sided PWB, the heat during soldering affects the resin; therefore, 1.6A keep the LED lamp more than 1.6mm afloat above the soldering position. A Solder the lead pins under the following conditions. (1.6mm or more from the resin package) 3. Reflow soldering Not acceptable ; ;; ; ; ; ;; ; ;; ;;; ;; ; ; ;;;;;;;; ;; Avoid forming a lead pin with the lead pin base as a fulcrum: be sure to hold a lead pin firmly when forming. Lead pins should be formed before soldering. (3) Installation using a holder During an LED lamp positioning, in case of using a holder, holder A should be designed to be smaller than the inside dimension of lead pins. Holder B should be designed to be larger than the outside dimension of lead pins. (Notes)¡Pay attention to the thermal expansion coefficient of the material used for the holder. A Since the holder expands and Holder contracts due to preheat and soldering heat, mechanical B stress may be applied to the lead pins, resulting in disconnection. 2 Notice Internet In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet address for Electronic Components Group http://sharp-world.com/ecg/

ブランド

SHARP

現況

2016年4月2日、シャープは台湾の鴻海(ホンハイ)精密工業から3888億円の出資を受け入れる契約を正式に結んだ。鴻海は10月までに支払って議決権の66%を握り、シャープを買収する。日本の大手電機メーカーとしてシャープは初めて外資の傘下に入る

会社名

シャープ株式会社

本社国名

日本

事業概要

液晶の応用技術を軸とした製品や各種電子部品の製造メーカー。

供給状況

 
Not pic File
データシート
pdf

Hot Offer

弊社在庫及び仕入れ先からのOffer

型式 数量 D/C・lead 備考 選択
GL3HD43 56個 N/A N/A
GL3HD43 56個 N/A  

提携先在庫情報

型式 数量 D/C・lead 備考 選択
GL3HD43 950個    
GL3HD43を取扱っています。

クレバーテックの担当が在庫確認を行いemailにて御回答致します。
どれか1つを選択し「見積依頼」をクリックしてお問合せ下さい。

お支払方法

宅配業者の代金引換又は商品到着後一週間以内の銀行振込となります。


お取引内容はこちら
GL3HD43の取扱い販売会社 株式会社クレバーテック  会社情報(PDF)    戻る

cb 0001507090000  0991707141033  0881711101039  0992007211003 

類似型番をお探しのお客様はこちらをクリックして下さい。
GL3H08 GL3HD43 GL3HD44 GL3HD47 GL3HD62
GL3HD8 GL3HD804EOS GL3HD8TQ5 GL3HS43 GL3HS43C
GL3HS44 GL3HS443MMLED GL3HS62 GL3HS8 GL3HS804E0S
GL3HY2 GL3HY401E0S GL3HY401EOS GL3HY402E0S GL3HY402EOS
GL3HY43 GL3HY44 GL3HY44YELL0W GL3HY62 GL3HY63
GL3HY8 GL3HY804EOS GL3HY8T