SOLID TANTALUM ELECTROLYTIC CAPACITORS
F91
LOW ESR
Resin-molded Chip
Compliant to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category
Temperature Range
Capacitance Tolerance
Dissipation Factor (120Hz)
ESR (100kHz)
--55 to +125˚C (Rated temperature : +85˚C)
± 20%, ±10% (at 120Hz)
Refer to the table below.
Refer to the table below.
• After 1 minute's application of rated voltage, leakage current
at 20˚C is not more than 0.01CV or 0.5µA, whichever is greater.
• After 1 minute's application of rated voltage, leakage current
Leakage Current
at 85˚C is not more than 0.1CV or 5µA, whichever is greater.
• After 1 minute's application of derated voltage, leakage current
at 125˚C is not more than 0.125CV or 6.3µA, whichever is greater.
Capacitance Change
by Temperature
Type numbering system (Example : 10V 100µF)
1
2
3
4
5
6
7
8
9
10
F 9 1 1 A 1 0 7 M C
Damp Heat
(Steady State)
11
Taping code
(Refer to page 333 for details)
Case code
Capacitance tolerance
Rated capacitance Rated voltage
Temperature Cycles
Series
Capacitance Change Within ±5% of the initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
to Soldering Heat
C • N Case
Surge∗
After 2000 hours' application of rated voltage in series with a 3Ω resistor
at 85 ˚C , or derated voltage in series with a 3 Ω resistor at 125 ˚C ,
capacitors shall meet the characteristics requirements table below.
Capacitance Change......Within ±10% of the initial value
Dissipation Factor..........Initial specified value or less
Leakage Current............Initial specified value or less
Shear Test
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered
beforehand on a substrate, there shall
5N (0.51kg ¥ f)
be found neither exfoliation nor its sign
For 10±1 seconds
at the terminal electrode.
Terminal Strength
W1
After application of surge in series with a 33Ω resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 sucessive test cycles at 85˚C,
capacitors shall meet the characteristic requirements table below.
Capacitance Change....Within ±5% of the initial value
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
Endurance∗
L
Keeping a capacitor surface20
mounted on a substrate upside down R230
and supporting the substrate at both
of the opposite bottom points 45mm
apart from the center of capacitor,
45
45
the pressure strength is applied with
a specified jig at the center of
substrate so that the substrate may bend by 1mm as illustrated.
Then, there shall be found no remarkable abnormality on the
capacitor terminals.
H
W2
S
S
Dimensions
(mm)
L
6.0 ± 0.2
W1
W2
H
C
3.2 ± 0.2
2.2 ± 0.1
2.5 ± 0.2
S
1.3 ± 0.2
N
7.3 ± 0.2
4.3 ± 0.2
2.4 ± 0.1
2.8 ± 0.2
1.3 ± 0.2
220
10V
N Case
68
10V
C Case
∗ As for the surge and derated voltage at 125˚C, refer to page 332 for details.
Rated voltage (V)
Rated voltage (V)
Rated Capacitance (µF)
Rated Volt
Standard Ratings
V
Code
4
0G
1mm
Marking
Cap.
(µF)
At 40˚C 90 to 95% R.H. 500 hours (No voltage applied)
Capacitance Change Within ±10% of the initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
--55˚C / +125˚C 30 minutes each 5 cycles
Capacitance Change Within ±5% of the initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
10 seconds reflow at 260˚C,
5 seconds immersion at 260˚C
Resistance
Drawing
Case Code
+15% Max. (at +125˚C)
.
+10% Max. (at +85˚C)
--10% Max. (at --55˚C)
6.3
0J
10
1A
C
068
686
100
107
C
C
150
157
C
C
N
220
227
C
C•N
N
330
337
N
N
N
470
477
N
N
680
687
4V
N
6.3V
10V
Rated
Capacitance
(µF)
Case
code
Part Number
Leakage
Current
(µA)
Disspation
Factor
(% @120Hz)
ESR
(mΩ@100kHz)
150
220
330
470
680
100
150
220
220
330
470
68
100
150
220
330
C
C
N
N
N
C
C
C
N
N
N
C
C
N
N
N
F910G157MCC
F910G227MCC
F910G337MNC
F910G477MNC
F910G687MNC
F910J107MCC
F910J157MCC
F910J227MCC
F910J227MNC
F910J337MNC
F910J477MNC
F911A686MCC
F911A107MCC
F911A157MNC
F911A227MNC
F911A337MNC
6.0
8.8
13.2
18.8
27.2
6.3
9.5
13.9
13.9
20.8
29.6
6.8
10.0
15.0
22.0
33.0
12
12
10
16
18
8
12
14
10
14
16
8
10
10
12
18
250
250
100
100
100
250
250
250
100
100
100
300
250
100
100
100
In case of capacitance tolerance
system.
± 10% type, K will be put at 9th digit of type numbering
CAT.8100B
