ALUMINUM ELECTROLYTIC CAPACITORS
WG
Chip Type, Low Impedance
series
Chip type, operating over wide temperature range of to – 55 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2002/95/EC).
Low
Impedance
UD
Low
Impedance
WG
WF
Specifications
Item
Performance Characteristics
Category Temperature Range
– 55 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range
1 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
Tangent of loss angle (tan δ)
6.3
0.26
Rated voltage (V)
tan δ (MAX.)
10
0.19
16
0.16
25
0.14
35
0.12
50
0.12
Measurement frequency : 120Hz
6.3
2
4
Rated voltage (V)
Z– 25°C / Z+20°C
Impedance ratio
Z– 55°C / Z+20°C
ZT / Z20 (MAX.)
Stability at Low Temperature
10
2
4
16
2
3
35
2
3
25
2
3
50
2
3
The specifications listed at right shall be met
Capacitance change Within ±20% of the initial capacitance value
when the capacitors are restored to 20°C
tan δ
200% or less than the initial specified value
after the rated voltage is applied for 1000
Leakage current
Less than or equal to the initial specified value
hours at 105°C.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change Within ±10% of the initial capacitance value
maintained at 250°C. The capacitors shall meet the characteristic
tan δ
Less than or equal to the initial specified value
requirements listed at right when they are removed from the plate
Leakage current
Less than or equal to the initial specified value
and restored to 20°C.
Endurance
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Type numbering system (Example : 10V 100µF)
Chip Type
1
(φ4 to φ6.3)
Positive
Plastic platform
0.3 MAX.
Voltage
0.5 MAX.
Capacitance
C±0.2
3
4
5
6
7
8
9 10 11 12 13 14
Taping code
A±0.2
φD
code
4 to 6.3 GB
8 • 10 GS
A±0.2
E
B±0.2
φD±0.5
A2P
100
6V
105°C Marking
2
UWG 1 A 1 0 1 M C L 1 G S
+0.1
L -0.2
Lot No.
Capacitance tolerance (±20%)
Negative
H
Rated capacitance (100µF)
(φ8 × 6.2 )
Positive
105°C Marking
Plastic platform
0.3 MAX.
Voltage
C±0.2
Series name
A±0.2
Type
A±0.2
E
B±0.2
A2P
100
10V
φD±0.5
Trade mark
Rated voltage (10V)
0.5 MAX.
Capacitance
L±0.3
Lot No.
(φ8 × 10, φ10 × 10 )
Positive
Plastic platform
0.3 MAX.
Voltage
C±0.2
A±0.2
φD × L
A
B
C
E
L
H
4 × 5.4
5 × 5.4
6.3 × 5.4
8 × 6.2
8 × 10
10 × 10
1.8
2.1
2.4
3.3
2.9
3.2
4.3
5.3
6.6
8.3
8.3
10.3
4.3
5.3
6.6
8.3
8.3
10.3
1.0
1.3
2.2
2.3
3.1
4.5
5.4
5.4
5.4
6.2
10
10
0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
A±0.2
E
B±0.2
φD±0.5
A2P
220
25V
Trade mark
0.5 MAX.
105°C Marking
(mm)
Negative
H
Capacitance
Configuration
φD
code
4 to 6.3
CL
8 (6.2L)
CL
8 (10L) • 10 NL
L±0.5
Lot No.
Pressure relief vent
H
Negative
Voltage mark for 6.3V is 6V .
Dimension table in next page.
CAT.8100A
